Knowledge Base
Make sense of suspension tuning, one topic at a time.
Use the five topic areas below to understand where your question fits. Explore five expert-written technical articles covering shock tuning, nitrogen pressure, rebound damping, coilover spring rates, and shock servicing.
Find a suspension topic.
Choose a topic below or jump directly to one of our five technical articles. Need help with your setup? Ask a question.
Tuning
Understand adjustments, establish a baseline, and compare changes.
Valving
Explore how internal damping influences compression and rebound.
Spring Rates
Learn how spring selection relates to load, ride height, and travel.
Troubleshooting
Describe unwanted behavior and identify what to check first.
Shock Tuning & Suspension Troubleshooting · Technical Article #1
Why Does My Truck Ride Harsh Over Small Bumps but Still Bottom Out on Big Hits?
The Customer's Question
“My truck beats me up over small bumps and washboard roads, but when I hit a bigger bump or G-out, it bottoms out. What's going on?”
Damping Theory Expert Answer
When a truck rides harsh over small bumps but still bottoms out on larger impacts, you need to evaluate the complete suspension setup before making changes to the shock valving.
There are several critical areas I would inspect.
- 1. Check the Nitrogen Gas PressureVerify that the nitrogen pressure meets the shock manufacturer's specifications. Incorrect gas pressure can affect shock performance and should be addressed before evaluating other tuning changes.
- 2. Inspect Coilover Spring PreloadIf the vehicle uses coilover shocks, determine how much spring preload is required to achieve the desired ride height.
Excessive preload may indicate that the spring setup needs further evaluation.
- 3. Check for Spring Coil BindInspect the springs to determine whether they are approaching or experiencing coil bind during suspension compression.
- 4. Evaluate the Dual-Rate Spring CrossoverIf the coilovers use a dual-rate spring setup, determine whether the suspension transitions from the initial combined spring rate to the lower spring's rate too early or too late.
The crossover point can significantly affect suspension response.
- 5. Measure the Spring Divider-to-Crossover Ring DistanceAt normal ride height, measure the distance between the spring divider and the crossover rings.
This helps establish when the suspension transitions between spring rates during compression.
- 6. Inspect the Number of Open Piston Bleed HolesDetermine how many bleed holes are open in the shock piston.
Depending on the application, changing the number of open bleed holes may be part of correcting the damping characteristics.
- 7. Verify Piston Bleed Hole SizeCheck the diameter of the piston bleed holes.
Depending on the application, increasing bleed-hole diameter, opening additional bleed holes, or combining both approaches may be considered. These changes must be evaluated alongside the rest of the shock's valving configuration.
- 8. Review Shock Service HistoryAsk when the shocks were last serviced.
Before recommending valving changes, determine whether the shocks require inspection or maintenance.
The Damping Theory Approach
A harsh ride combined with bottoming out does not automatically mean the shock needs more compression damping.
Start by evaluating nitrogen pressure, spring preload, potential coil bind, dual-rate crossover settings, piston bleed configuration, and shock service history.
Once those factors are understood, you can make a more informed decision about whether the problem involves spring setup, shock condition, or internal valving.
Damping Theory | Diagnose First. Tune With Purpose.
Shock Maintenance & Troubleshooting · Technical Article #2
Nitrogen Gas Pressure: Why It Matters in Off-Road Shocks
Why Do Off-Road Shocks Need Nitrogen Gas Pressure?
Nitrogen gas pressure is essential for proper operation of gas-pressurized shock absorbers.
In a typical reservoir-equipped shock, an Internal Floating Piston (IFP) separates the nitrogen gas from the hydraulic oil.
The nitrogen applies pressure to the hydraulic oil through the IFP while accommodating the oil volume displaced as the shock shaft enters the shock body during compression.
Maintaining positive pressure in the hydraulic system helps reduce the risk of cavitation during repeated compression and rebound cycles.
Understanding Cavitation, Air Entrainment, and Aeration
These three terms are commonly used when discussing shock absorber performance, but they describe different conditions.
Cavitation
Cavitation occurs when localized pressure within the shock oil drops low enough for vapor bubbles to form. When pressure increases, these vapor bubbles can collapse.
Cavitation can disrupt consistent hydraulic damping, particularly during rapid or repeated shock cycling.
Air Entrainment
Air entrainment occurs when air or another gas becomes mixed into the shock oil.
Entrained gas can make the hydraulic fluid more compressible, potentially causing foaming, inconsistent damping, and reduced shock performance.
Aeration
Aeration is a broader term commonly used in the suspension industry to describe gas bubbles dispersed throughout the shock oil.
Aeration can affect damping consistency because the oil-and-gas mixture behaves differently from properly bled hydraulic oil.
How Nitrogen Pressure Relates to These Conditions
In a reservoir-equipped shock, nitrogen pressure acts on the hydraulic oil through the Internal Floating Piston (IFP).
The IFP separates the nitrogen gas from the shock oil while allowing the nitrogen chamber to accommodate the oil volume displaced by the shock shaft during compression.
Maintaining the manufacturer's specified nitrogen pressure helps keep the hydraulic system pressurized, reducing the risk of cavitation during shock operation.
However, proper nitrogen pressure does not replace correct shock bleeding procedures. Air trapped in the oil during assembly must be removed through proper servicing and bleeding techniques.
Why Is Maintaining the Correct Nitrogen Pressure Important?
Nitrogen pressure should be checked periodically against the shock manufacturer's recommended specification.
Insufficient nitrogen pressure can contribute to inconsistent damping performance, particularly during repeated or aggressive suspension cycling.
Always follow the manufacturer's pressure specifications for the particular shock model.
How Should Nitrogen Pressure Be Checked?
For the shock configuration described here:
- 1. Fully extend the shock shaft.The shock should be at full extension when checking nitrogen pressure.
- 2. Remove the load from the shock.The suspension must be unloaded so the shock is not supporting vehicle weight.
- 3. Ensure the limit strap is not under tension.The limit strap must not restrict full shock extension.
- 4. Check the nitrogen pressure.Use the appropriate charging equipment and compare the reading against the manufacturer's specification.
Follow the manufacturer's service procedure, including any temperature and shaft-position requirements specific to the shock.
The Damping Theory Approach
Correct nitrogen pressure is one of the first things to verify when diagnosing shock performance problems.
The IFP, nitrogen charge, and hydraulic oil work together to maintain consistent damping throughout shock operation.
Damping Theory | Diagnose First. Tune With Purpose.
Shock Tuning & Suspension Troubleshooting · Technical Article #3
How Do I Know If My Shocks Have Too Much or Too Little Rebound Damping?
What Is Rebound Damping?
Rebound damping controls the rate at which a shock absorber extends after being compressed.
Proper rebound damping allows the suspension to extend quickly enough to maintain tire contact with the terrain while providing enough control to prevent excessive or uncontrolled extension.
Both excessive and insufficient rebound damping can negatively affect vehicle handling and stability.
1. Too Much Rebound Damping: Shock Packing
When rebound damping is too slow or restrictive, the suspension may experience a condition known as shock packing.
Packing occurs when the shock cannot extend quickly enough between successive bumps or impacts.
At high shock shaft speeds, this condition often becomes noticeable by the third or fourth consecutive bump.
Here's what happens:
- The suspension compresses as the vehicle encounters the first bump.
- Excessive rebound damping prevents the shock from extending quickly enough before the next bump.
- With each successive bump, the shock operates progressively deeper into its compression travel.
- By the third or fourth bump, the shock may have very little compression travel remaining.
- When the next bump arrives, the suspension can no longer compress sufficiently to absorb the impact.
The result: The rear of the vehicle can suddenly step out to the left or right, depending on the bump and terrain conditions.
This happens because the suspension has effectively packed down, leaving insufficient compression travel to absorb the next impact.
Common symptoms include:
- Increasing harshness over consecutive bumps.
- The suspension feeling progressively lower or more compressed.
- Reduced available compression travel.
- Loss of rear tire traction.
- The rear of the vehicle suddenly stepping sideways after several high-speed impacts.
2. Too Little Rebound Damping: Flopping
When rebound damping is too fast or unrestricted, the suspension may exhibit a flopping sensation.
This occurs when the shock extends too quickly and does not provide enough damping control during rebound.
Common symptoms include:
- A loose or uncontrolled suspension feeling.
- Excessive suspension movement after impacts.
- A flopping sensation during higher shock shaft speeds.
- Reduced vehicle stability and predictable handling.
3. Light Rebound Damping: Excessive Vehicle Rise
Another symptom of insufficient rebound damping can occur following a hard compression hit.
When the suspension compresses aggressively and rebound damping is too light, the stored energy in the springs can cause the suspension to extend rapidly.
This may cause the vehicle to rise above its normal ride height as the suspension rebounds from the impact.
This behavior can make the vehicle feel unsettled following large bumps, jumps, or G-outs.
The Damping Theory Approach
When diagnosing rebound damping, I pay close attention to how the suspension behaves after compression.
Too much rebound damping: The shock extends too slowly, potentially causing progressive packing, loss of compression travel, and rear-end step-out over consecutive bumps.
Too little rebound damping: The shock extends too quickly, potentially causing flopping, uncontrolled movement, and excessive vehicle rise after a hard compression hit.
The goal is to achieve enough rebound control to stabilize the vehicle while allowing the tires to follow the terrain.
Damping Theory | Diagnose First. Tune With Purpose.
Spring Rates & Suspension Setup · Technical Article #4
How Do I Determine the Correct Spring Rates for My Coilover Shocks?
What Determines the Correct Coilover Spring Rate?
Selecting the correct coilover spring rates starts with understanding the vehicle's corner weights and the amount of spring support required to maintain the desired ride height.
Several factors must be considered:
- Vehicle corner weights: The weight supported at each corner of the vehicle.
- Desired ride height: The amount of shock shaft travel available in compression and extension at normal ride height.
- Shock mounting position: Where the shock mounts to the chassis and axle or suspension arm.
- Motion ratio: The relationship between wheel movement and shock shaft movement.
- Spring configuration: Whether the coilover uses a single spring or a dual-rate arrangement.
These factors work together to determine the spring rates needed for the application.
Real-World Example: Jeep JK Front Suspension
One of the most common spring-rate applications customers ask about is a relatively stock-weight Jeep Wrangler JK front end fitted with coilovers.
Consider a standard Jeep JK with no significant additional weight installed over the front axle.
- Vehicle: Jeep Wrangler JK
- Shock: 2.0-inch diameter × 12-inch travel coilover
- Mounting: Upper mount on the chassis near the original coil spring location; lower mount directly to the front differential/axle
- Shock orientation: Nearly vertical
- Approximate motion ratio: 1:1
- Desired exposed shock shaft at ride height: 6–7 inches
For this particular configuration, a common starting spring combination is 200 lb/in upper spring over a 200 lb/in lower spring. This is an application-specific starting point, not a universal recommendation for every Jeep JK.
Understanding the Initial Dual-Spring Rate
When two springs are stacked in series and both remain active, their combined spring rate is calculated as:
Combined rate = (Upper spring rate × Lower spring rate) ÷ (Upper spring rate + Lower spring rate)
Using two 200 lb/in springs: (200 × 200) ÷ (200 + 200) = 100 lb/in.
This produces an initial combined spring rate of 100 lb/in.
When the spring divider contacts the crossover rings and the upper spring is effectively taken out of the active spring combination, the suspension transitions to the lower spring's rate of 200 lb/in.
The crossover position determines when this transition occurs during compression.
Why Spring Rates Matter on a Rear 4-Link Suspension
Spring selection is particularly important on rear 4-link suspension systems. Correct spring rates and crossover settings help support the vehicle at the desired ride height while contributing to bottom-out control during hard impacts.
The shock's compression damping and bump stops also play important roles in managing suspension energy and preventing excessive bottoming.
Properly matching spring rates, crossover settings, compression damping, and bump stops helps reduce the loads placed on the shock during aggressive suspension compression.
The Damping Theory Approach
Correct spring rates are not selected by vehicle model alone.
I start with the vehicle's corner weights, suspension geometry, shock mounting location, motion ratio, and desired ride height.
From there, I evaluate the spring combination and crossover settings to establish the appropriate initial rate and compression characteristics.
Damping Theory | Diagnose First. Tune With Purpose.

Shock Maintenance & Troubleshooting · Technical Article #5
How Do I Know If My Shocks Need Servicing Rather Than a Tuning Adjustment?
When Is Shock Servicing Necessary?
Shock absorbers require periodic servicing to maintain consistent damping performance and reliable suspension operation.
Before attempting to correct a ride-quality problem through valving changes or external adjustments, it's important to determine whether the shocks are mechanically sound and operating correctly.
Here are the primary warning signs I look for when evaluating a shock absorber.
1. Leaking Shock Seals
Inspect the shock body, shaft seal area, and reservoir connections for signs of oil leakage.
Oil leaking past the seals may indicate worn or damaged sealing components that require service.
2. Shock Shaft Pitting, Damage, or Bending
Carefully inspect the shock shaft for:
- Pitting or corrosion.
- Scratches or damaged shaft surfaces.
- Signs of a bent shock shaft.
Damaged shafts can accelerate seal wear, cause oil leaks, and interfere with proper shock operation.
3. Excessive Wear in Upper and Lower Heim Joints or Bushings
Inspect the upper and lower shock mounting points.
Excessive wear in the heim joints or bushings can introduce unwanted movement, noise, and alignment problems.
Worn mounting components should be addressed before evaluating shock tuning.
4. Minimal or No Nitrogen Gas Pressure
Check the nitrogen pressure against the shock manufacturer's specifications.
A shock with minimal or no gas pressure may not operate correctly and can exhibit inconsistent damping performance.
On shock designs where nitrogen pressure normally produces an extension force, a shock that no longer extends on its own may indicate insufficient gas pressure or another internal problem.
5. Oil Present in the Nitrogen Chamber
In a shock equipped with an Internal Floating Piston (IFP), the nitrogen gas and hydraulic oil should remain separated.
An excessive amount of oil escaping from the nitrogen charging valve during an appropriate service inspection can indicate that oil has entered the nitrogen chamber.
This may point to an IFP sealing problem or another internal issue requiring shock disassembly and inspection.
Important: Nitrogen chambers can contain substantial pressure. Checking or releasing gas through the Schrader valve should be performed only with appropriate equipment and procedures. Do not depress the valve core casually.
6. Shock Mileage and Service History
Determine how many miles the shocks have accumulated since they were last serviced or originally assembled.
Service requirements depend on shock design, driving conditions, and vehicle use.
Shocks used in aggressive off-road environments may require more frequent inspection and servicing than shocks used primarily on the street.
7. Little or No Damping Control
Shocks that need servicing may exhibit:
- Little or no damping resistance.
- Inconsistent damping during compression and rebound.
- Excessive bouncing or uncontrolled suspension movement.
- Changes in damping behavior as the shocks cycle or heat up.
These symptoms can indicate internal wear, degraded oil, gas-pressure problems, or other mechanical issues.
The Damping Theory Approach
Before making tuning changes, I inspect the shock's mechanical condition, nitrogen pressure, shaft condition, mounting components, and service history.
If the shock is leaking, damaged, improperly pressurized, or providing inconsistent damping, servicing should take priority over valving adjustments.
A properly functioning shock is the foundation of an effective suspension tune.
Damping Theory | Diagnose First. Tune With Purpose.
Put your setup in context.
Ask about a suspension issue, or tell us about your vehicle and goals for a shock quote.
